Filter by attributes Directions/Instructions <b>Automatic Scrubbing Machines</b><br /> <ul> <li>1. Dust mop or sweep.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add four (4) oz. per gallon (30mL per liter) of this product to lukewarm water. Scrub floor with product. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely</li> </ul> <b>Mop and Bucket Cleaning </b><br /> <ul> <li>1. Dust mop or sweep.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add two (2) oz. per gallon (15 mL per liter) of this product to lukewarm water. Mop floor clean with this product. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely.</li> </ul> <b>Stone/Concrete Floor Daily cleaning (Automatic Scrubbing Machine):</b> <br /> <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add (1) oz. per gallon of this product to warm water. Scrub floor with product and Twister™ Intellipad®. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely.</li> </ul> <b>Stone/Concrete Floor Rejuvenation (Mop and Bucket method):</b> <br /> <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Clean floor with a neutral floor cleaner according to label directions.</li> <li>4.Add thirteen (13) oz. per gallon (101 mL per liter) of this product to lukewarm water. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.</li> <li>5. Let air dry.</li> <li>6. For optimal gloss, burnish the floor with Twister™ Intellipad®.</li> </ul> <b>Stone/Concrete Restoration:</b> <br /> <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Clean floor with a neutral floor cleaner according to label directions.</li> <li>4. Dilute this product with lukewarm water at a 1:1 dilution ratio. Apply up to 2 coats using a string mop or flat mop until desired shine is achieved. Be sure to evenly cover the entire floor. Do not rinse floor after cleaning.</li> <li>5. Let air dry.</li> <li>6. For optimal gloss, burnish the floor with Twister™ Intellipad®.</li> </ul> <b>Best Results<br /></b> <ul> <li>Do not use on surfaces colder than 50°F/10°C</li> <li>To avoid contamination, do not return unused product to original container.</li> </ul> <b>Note:</b> Floors will be slippery when wet or contaminated with foreign materials. Promptly clean-up spills and foreign materials. Not intended for use in outdoor areas. Meets ASTM D-2047 requirements for slip resistance. Rubber Floors: For optimum appearance, alternate use of this product at standard dilution and ProfiTM/MC Degreaser once desired shine is achieved. On heavily worn rubber floors apply up to three coats of WiwaxTM/MC emulsion cleaner using the mop and bucket cleaning instructions with a 1:1 dilution ratio until desired shine is achieved. If high gloss is desired, apply instead, three coats of Carefree Floor Finish. <b>Recommended Dilutions:</b><br /> <ul> <li>Heavy Soil, Parts Wash and Immersion Cleaning: 1:24 - 1:32</li> <li>Medium Soil, General Cleaning, Floor Cleaning: 1:64 or 1:128</li> <li>Equipment, Machinery and Pressure Washing Cleaning: 1:128</li> <li>Light Soil, Auto Scrubbing: 1:256</li> </ul> <b>Sprap-and-wipe Cleaning:</b> Spray product onto surface to be cleaned. Wipe surface and rinse. In heavily soiled areas, allow the solution to penetrate for 2-4 minutes. When cleaning glass, ceramic tile, aluminum and painted surfaces, do not allow surface to dry. Rinse thoroughly.<br /><br /><b>Floor Cleaning:</b> Place slippery floor signs around the area. Apply solution onto the floor with a mop or autoscrubber. Pick up all excess solution from the floor. Rinse thoroughly to avoid corrosion.<br /><br /><b>Food Processing Areas:</b> Before using this product in food processing establishments, food products and packaging materials must be removed from the area or carefully protected. After using this product, all surfaces in the area must be thoroughly rinsed with potable water. Avoid<br />contamination of food during use or storage. <b>Use instructions </b><br /><b>Mop and Bucket Method</b><br /> <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Mop floors. No rinsing is necessary in non-food preparation areas.</li> </ul> <b>Automatic Scrubber Method</b> <br /> <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Clean and scrub floors.</li> <li>Trail mop machine turns, edges and low spots in the floor to pick up cleaning solution left behind by machine.</li> </ul> <b>Spray and Wipe Cleaning </b><br /> <ul> <li>Fill, dilute or dispense product according to label directions.</li> <li>Spray and wipe surfaces clean.</li> </ul> <b>For RTD® Use:</b><br /> <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul> <b>Use instructions</b> <br /> <ul> <li>Spray on hard surfaces to be cleaned.</li> <li>Allow power cleaner to penetrate and lift soils.</li> <li>Wipe with a clean cloth.</li> <li>Does not require a water rinse after use.</li> <li>Do not use on glass, aluminum or water-based paint.</li> <li>Suitable for use in areas where food or packaging will not come in contact with spray or surface during or after the use of this product.</li> </ul> <b>Use instructions</b><br /> <ul> <li>Use BreakDownTM/MC Odor Eliminator on all organic odors and stains.</li> <li>General Deodorizing: Dilute 1:32 with water (4 ounces per gallon/ 31 mL per liter).</li> <li>Washroom: Dilute 1:20 with water (6 ounces per gallon/50 mL per liter). Apply around urinals, toilets, on floors and in trash receptacles.</li> <li>Plumbing Pipes (drains, sinks, disposals, toilets): Pour 4 ounces (120 mL) of BreakDownTM/MC Odor Eliminator into drain pipes 2 times per week when drain flow is lowest.</li> <li>Carpet Odors and Stains for Spotting: Test carpet for colorfastness. Use BreakDownTM/MC Odor Eliminator full strength. Follow good spotting procedures. Re-apply BreakDownTM/MC Odor Eliminator. Let stand 20 minutes.</li> <li>General Carpet Cleaning: Dilute 1:64 with diluted cleaning solution (2 ounces per gallon/15.6 mL per liter).</li> </ul> <p><b>Directions for Use</b></p> <p>This product is for cleaning glass, windows, mirrors, plastic, Plexiglass and a variety of other water washable surfaces.<br />Dilute 2 oz./gal. or 16 mL/L (1:64) with cold water. Spray glass cleaner on surface to be cleaned and wipe with a lint-free towel or squeegee.<br />Improper use or dilution of this product may affect cleaning performance, result in excess waste or may damage surfaces also may increase risk of health effects. Gloves and goggles recommended personal protection equipment. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers.</p> <p><b>Directions for Use</b></p> Recommended for use on all types of resilient tile (vinyl composition, vinyl, linoleum) and properly sealed hard surfaces (marble, terrazzo). <br /><br />RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures and humidity may extend dry time. 4 - 5 coats of finish are recommended. Note: This product is a self sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a sealer will enhance gloss and long term performance. <br /><br />ROUTINE MAINTENANCE: Sweep large debris and dust mop (using a water-based treatment). Damp mop or automatic scrub using a neutral pH cleaner. Buff or burnish the floor as desired. The use of a cleaner/restorer is recommended to condition the floor and extend the time between top scrub and recoating. <br /><br />INTERIM MAINTENANCE: Sweep large debris and dust mop (using a water-based treatment). Top scrub the floor using a top scrub cleaner and recommended floor pad to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. <br /><br />Note: Slip resistance meets or exceeds standard, (ASTM D 2047-04) James Machine 0.5 minimum. <p><b>Instructions:</b></p> <p>Recommended as a floor and wall cleaner in all departments of federally-inspected meat and poultry plants. Particularly useful in automotive repair shops, department stores, nursing homes & hospitals, child day care services, eating & drinking establishments, operators of apartment buildings, cleaning & maintenance services, hotels & motels, schools & educational facilities and sports & recreational clubs</p> <p><b>It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.</b></p><p>DILUTION: 1:64 (660 ppm quat) - 2 ounces per gallon of water</p><p>This product is not for use on medical device surfaces.</p><p><b>DISINFECTION/CLEANING/DEODORIZING DIRECTIONS:</b>Remove heavy soil deposits from surface, then thoroughly wet surface with a use-solution of 2 ounces of the concentrate per gallon of water. The use-solution can be applied with a cloth, mop, sponge, or coarse spray or by soaking. For sprayer applications, use a coarse spray device. Spray 6-8 inches from the surface, rub with a brush, cloth or sponge. Do not breathe spray. Let solution remain on surface for a minimum of 10 minutes. Rinse or allow to air dry. Rinsing of floors is not necessary unless they are to be waxed or polished. Food contact surfaces must be thoroughly rinsed with potable water. This product must not be used to clean the following food contact surfaces: utensils, glassware, and dishes.<b>For Human Coronavirus,</b>treated surfaces must remain wet for 1 minute. Wipe dry with a clean cloth, sponge or mop or allow to air dry.<b>For Influenza Virus Type A</b>, treated surfaces must remain wet for 2 minutes. Wipe dry with a clean cloth, sponge or mop or allow to air dry. Prepare a fresh use-solution daily or more often if the solution becomes visibly dirty or diluted.<b>FUNGICIDAL DIRECTIONS:</b>For use in areas such as locker rooms, dressing rooms, shower and bath areas, and exercise facilities follow disinfection directions.<b>MILDEWSTATIC INSTRUCTIONS:</b>Will effectively control the growth of mold and mildew, plus the odors caused by them when applied to hard, nonporous surfaces such as walls, floors and table tops. Apply use-solution at 2 ounces per gallon of water with a cloth, mop, sponge, or coarse spray. Make sure to wet all surfaces completely. Let air dry. Repeat application weekly or when growth reappears.<b>*KILLS HIV-1 (AIDS VIRUS) AND HBV (HEPATITIS B VIRUS) AND HCV (HEPATITIS C VIRUS) ON PRECLEANED, ENVIROMENTAL SURFACES / OBJECTS PREVIOUSLY SOILED WITH BLOOD BODY FLUIDS</b>in health care settings or other settings in which there is an expected likelihood of soiling of inanimate surfaces/objects with blood / body fluids, and in which the surfaces / objects likely to be solid with blood / body fluids that can be associated with the potential for transmission of Human Immunodeficiency Virus Type I (HIV-1) (associated with AIDS) or Hepatitis B Virus (HBV) or Hepatitis C Virus (HCV).</p><p><b>SPECIAL INSTRUCTIONS FOR CLEANING AND DECONTAMINATION AGAINST HIV-1 (AIDS VIRUS) OR HBV OR HCV OF SURFACES / OBJECTS SOILED WITH BLOOD / BODY FLUIDS:</b>Personal Protection: Disposable protective gloves, gowns, face mask and eye coverings, as appropriate, must be worn during all cleaning of blood / body fluids and during decontamination procedures. Cleaning Procedures: Blood / body fluids must be thoroughly cleaned from surfaces / objects before application of disinfectant. Contact time : HIV-1 (AIDS virus) is inactivated after a contact time of 4 minutes at 25 C (77 F)(room temperature. HBV and HCV are inactivated after a 10 minute contact time. Use a 10-minute contact time for other viruses, fungi and bacteria listed. Disposal of Infectious Materials: blood / body fluids should be autoclaved and disposed of according to federal, state and local regulations for infectious waste disposal.</p> <p><b>Usage Instructions:</b></p> <p>Floors: Mix 1/4 cup in a gallon of room temperature water. Bathrooms & Walls: Use on sponge and clean. Due to formula difference, do not use Fabuloso Multi-Purpose Pourable Liquid Cleaner as a refill for Fabuloso Multi-Purpose Spray.</p> <p><b>Usage Instructions:</b></p> <p>Use Fabuloso<sup>®</sup> on sinks, toliets, tubs, showers, floors, sealed wood surfaces, appliances, counters, windows, mirrors, walls, doorknobs, and furniture.</p> <p>WITH A SPONGE: POUR ON A SPONGE AND CLEAN<br />WITH A BUCKET: MIX 1/4 CUP IN A GALLON OF WATER</p> <p><b>Usage Instructions:</b></p> <ul> <li>Wet surface. Sprinkle Ajax cleanser freely. Rub lightly with sponge to make a paste. Clean and rinse. Use Ajax on pots and pans, porcelain, bathroom fixtures, ceramic tiles, and even tough outdoor items like barbeque grills and garbage cans.</li> <li>Use caution and test a small area first on delicate surfaces such as fiberglass, imitation marble, plastics and enameled appliances. Use plenty of water, rub gently and rinse well. Do not use on silver, fabrics, painted surfaces or plexiglass. Store in cool, dry place. Do not re-use empty container. Discard in trash.</li> </ul> <p>Be sure to pretest before using.</p><p>HARD SURFACE CLEANING AND ODOR CONTROL: Dilute 4 - 8 ounces per gallon of water and apply directly to surface.</p><p>RESTROOMS: To deodorize urinals and bowls, apply to surfaces and surrounding area.</p><p>FLOORS: Dilute 2 - 5 ounces per gallon and mop directly onto floor. Pour excess directly down the drain.</p><p>CARPETS: For pet odors, pour directly on odor spot. Blot with a clean white cloth. Repeat if the odor persists. </p><p>CARPET MACHINES: To deodorize carpets, add 1/4 cup of product to the solution tank. </p><p>DRAINLINES AND DOWN PIPES: Use product a minimum of 2 times weekly, to a maximum of 4 times. Start on the lowest floor and work 1 floor per day. Do not treat the same floor twice. When the top floor is reached, continue treatment for the top floor only. </p><p>PIPE SIZE/DOSAGE/FREQUENCY: 2"/4 oz./2 times/wk.; 4"/8 oz./2 times/wk.; 6"/12 oz./2 times/wk.; 8"/16 oz./2 times/wk. </p><p>GREASE TRAPS: For less than 20 cubic feet capacity, add 4 - 5 oz. of product daily by pouring into a sink or pipeline closest to the trap. Perform when the traps are used the least. Flush down with 1 cup of lukewarm water. For traps larger than 20 cubic feet, add 8 - 10 oz. daily using the same procedure. </p><p>SEPTIC TANKS: Initial treatment, add 1 pint per 25 cubic feet capacity. Thereafter, use 8 oz. per week. Pour directly into toilet and flush. NOTE: Do not subject this product to disinfectants, boiling water or chlorinated products. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers.</p> <p>Cleans as easy as: 1) Shake, 2) Spray, 3) Wipe.</p> <p>For best results, spray onto cloth or hold can upright 6-8" from surface to be cleaned. Safe for all finished, sealed surfaces.</p> <p>Dilute with water for general cleaning. This degreaser is for use in schools, factories, kitchens, and food service. Not for use in food-preparation or food-contact areas. Particularly effective at removing ink, marker and crayon graffiti from desks, countertops and other washable surfaces. </p><p>FOR DISPENSING SYSTEM: Place product so that it will dispense diluted product at the dilutions listed below. </p><p>LIGHT SOIL: Dilute 2 oz./gal. or 16 mL/L (1:64) with water. </p><p>MODERATE SOIL: Dilute 4 - 5 oz./gal. or 31.25 - 38.5 mL/L (1:32 - 1:26) with water. </p><p>HEAVY SOIL: Dilute 8.5 oz./gal. or 66.7 mL/L (1:15) with water. </p><p>FOR USE WITH TRIGGER SPRAY BOTTLE: Spray properly diluted product to soiled areas and wipe with a clean cloth.</p><p>FOR USE WITH MOP BUCKETS: Fill mop bucket with properly diluted product as indicated by the soil levels and the dilution table above. Apply properly diluted product to the floor, let set 3 - 5 minutes. Pick up with tightly rung mop or wet/dry vacuum. </p><p>FOR USE IN AN AUTOMATIC SCRUBBER: Fill solution tank with properly diluted mixture of product. For heavy soils, use double scrub method of cleaning. For porous or grouted floors, scrub brushes may improve the removal of surface soils. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers.</p> <p>For best results, spray onto cloth or hold can upright 6-8" from surface to be cleaned. Safe for all finished, sealed surfaces.</p> <p>General Cleaning and Deodorizing:Use ¼ cup per gallon of water. No rinsing required except on rubber or asphalt tile. For tough jobs, use full strength and rinse immediately. For no-wax floors, only use diluted and rinse.</p> <p>Toilet Bowls:Pour ½ cup in the bowl and brush thoroughly, including under the rim.</p> <p>Not effective against rust stains. Dilute with cold water only. For GENERAL PURPOSE dilute 1:32 - 1:64 oz or 4 oz./gal - 2 oz./gal depending on soil level. Spray and wipe. GLASS: Dilute 1:64 or 2 oz./gal. Spray and wipe. SHOWERS: Dilute 1:32. For large areas use a portable pump up sprayer. Spray on tile, grout, fixtures and tub surfaces. Let stand for 5 minutes and rinse. For heavier stains agitation with a brush or sponge may be necessary to completely remove the stain. FLOORS: Dilute 1:64. Add directly to grout scrubber for removal of mold stains, soap scum, hard water deposits, or other common restroom soils. CARPET SPOTTING: Dilute 1:10 or 12 oz/gal. for heavy soils, dilute 1:20 or 6 oz./gal. for light to medium soils. For coffee as well as other water based stains. Apply a small amount of liquid to the stain. Agitate with a bone scraper and let stand for 3 - 5 minutes. Blot dry and rinse with clean water. Repeat as needed until the stain is completely removed.<br />Improper use or dilution of this product may affect cleaning performance, result in excess waste or may damage surfaces also may increase risk of health effects. Gloves and goggles recommended personal protection equipment. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers.</p> <p>Pro Tips:</p> <p>The Calcium, Lime & Rust Stain Remover should be rinsed off quickly after applying, so keep a bucket of clean water handy for easy rinsing.</p> <p>Instructions:</p> <p>May etch older sinks, tubs and tiles. Test all surfaces in a hidden area before use. Directions: TO CLEAN TUBS, TOILET BOWLS AND SINKS: Mix 50/50 Calcium, Lime & Rust Stain Remover and warm water and apply to surfaces with brush, sponge or cloth. Rinse with clean water within 60 seconds. Tough stains may require a second application at full strength. TO CLEAN STUCCO, CEMENT AND BRICK: Mix 50/50 Calcium, Lime & Rust Stain Remover and warm water and apply to surfaces with brush, sponge or cloth. Rinse after 5-10 minutes. Tough stains may require a second application at full strength.</p> <p>Removes tough grease, oil, carbon and most stubborn soils from appliances, counters, equipment, floors, kitchen surfaces, walls, showers, sinks, stainless steel and tile. Not recommended for use on glass or water based paints. This is a ready-to-use product. No mixing required. Leaves no residue or streaks. Spray surface. Wipe clean with a lint free towel or sponge.</p> <p>Shake well before using.</p> <p>General Cleaning:</p> <ul> <li>Hold can upright and spray about eight inches from surface.</li> <li>Wipe with soft, clean cloth for best results.</li> <li>If using on electronic equipment, spray product directly onto cloth, then dust as usual.</li> </ul> <p>This low foaming degreaser utilizes Aqua-Transolvency™ technology to remove rubber tire marks, carbon, heavy grease and oil from concrete floors.</p><p>NOTE: Do not use on glass.</p><p>LIGHT SOIL Dilute 4 oz./gal. or 31 mL/L (1:32) with water.</p><p>MODERATE SOIL Dilute 8 oz./gal. or 63 mL/L (1:16) with water.</p><p>HEAVY SOIL Dilute 13 oz./gal. or 100 mL/L (1:10) with water.</p><p>VERY HEAVY SOIL Dilute 26 oz./gal. or 200 mL/L (1:5) with water.</p> <p>Turn spray nozzle to ON position.</p> <ul> <li>Simply spray and wipe with a soft cloth or paper towel until surface is clean.</li> <li>No rinsing necessary.</li> <li>Use to clean surfaces such as wood, laminate, electronics, chrome, glass, mirrors and metal.</li> <li>If using on electronic equipment, spray product directly onto cloth and follow manufacturer instructions.</li> </ul> <p>Before using on an unknown surface, test on an inconspicuous area. Not suitable for unsealed wood, unsealed marble or unsealed granite. Do not use with other household cleaners.</p> <p>Usage Instructions:</p> <p>Use Fabuloso<sup>®</sup> on sinks, toliets, tubs, showers, floors, sealed wood surfaces, appliances, counters, windows, mirrors, walls, doorknobs, and furniture.</p> <p>WITH A SPONGE: POUR ON A SPONGE AND CLEAN<br />WITH A BUCKET: MIX 1/4 CUP IN A GALLON OF WATER</p> <ul> <li>Available in dilution control for ease in use, safety and cost control</li> <li>Can also be used for carpet spotting and extraction cleaning</li> <li>Use in autoscrubbers, mop and bucket and spray-and-wipe applications</li> </ul> <ul> <li>Can be used on glass and many washable surfaces such as chrome, stainless steel, sinks, bathroom fixtures and laminate surfaces such as countertops.</li> <li>Do not use on copper or brass as repeated use may discolor these surfaces.</li> </ul> <ul> <li>For use as daily and general cleaner.</li> <li>Versatile formula that performs in a variety of application methods such as an autoscrubber, spray and wipe and mop and bucket</li> </ul> <ul> <li>In a well-ventilated area, mix equal amounts of CLR and warm water.</li> <li>Test on a hidden area before applying to the entire surface and apply directly to the stain with a brush, cloth, or sponge and let soak for 2 minutes.</li> <li>Rinse promptly with cold water.</li> <li>Never leave CLR on an area for longer than two minutes or mix with other household cleaners or bleach.</li> <li>Never leave CLR on an area for longer than two minutes or mix with other household cleaners or bleach.</li> </ul> <ul> <li>Pre-clean heavily soiled areas.</li> <li>Apply product by coarse trigger spray to hard, non-porous inanimate surfaces.</li> <li>All surfaces must remain visibly wet for 1 minute. Use 5-minute contact time for TB and a 3 minute contact time for fungi.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul> Note: Rinsing is not necessary unless floors are to be coated with finish or restorer. All food contact surfaces must be rinsed with potable water. Do not use on glassware, utensils, or dishes. Prior to first use on a particular surface, it is recommended to test in a small, discreet area if there is concern of incompatibility, or contact a Diversey representative.<br /><br /><b>To Spot Sanitize Soft Surfaces</b><br /> <ul> <li>Remove gross filth prior to sanitization.</li> <li>Hold bottle upright 6" - 8" from surface.</li> <li>Spray until fabric is wet. DO NOT SATURATE. Allow surface to remain wet for 30 seconds.</li> <li>Gently blot with a clean, damp, color safe cloth and/or let air dry. For difficult odors or heavy fabrics, repeat application.</li> <li></li> </ul> <ul> <li>Spray & wipe cleaner for hard surfaces</li> <li>Use to remove marker and paint</li> <li>Cleaner/Degreaser for shops and kitchens NSF C-1</li> </ul> <ul> <li>Use as a spray-and-wipe application</li> <li>Use on any water-washable hard surface</li> </ul> <ul> <li>Wear safety glasses & gloves </li> <li>Spray onto surface</li> <li>Wait for cleaner to penetrate soil</li> <li>Wipe clean with a lint free cloth</li> <li>Do not use on glass or varnished surfaces</li> </ul> <ul> <li>Wear safety glasses & gloves</li> <li>Spray onto surface</li> <li>Wipe clean</li> <li>Allow to air dry</li> </ul> <ul> <li>Wear safety glasses & gloves</li> <li>Test in an inconspicuous area</li> <li>Spray onto sponge, cloth, or brush and apply to surface</li> <li>Wipe dry or rinse with clean water</li> <li>Do not use on glass or aluminum</li> </ul> <ul> <li>Wear safety glasses & gloves</li> <li>Test inconspicuous area</li> <li>Apply to stained area, agitate with bone scraper</li> <li>Blot stain with clean towel</li> </ul> <ul> <li>Wear safety glasses & gloves</li> <li>Use 2 oz of product per 1 gallon of water</li> <li>Apply to surface</li> <li>Scrub as needed and allow to air dry</li> </ul> Be sure to pretest before using. *GREASE TRAPS: For less than 20 cubic feet capacity, add 4 - 5 oz. of product daily by pouring into a sink or pipeline closest to the trap. Perform when the traps are used the least. Flush down with 1 cup of lukewarm water. For traps larger than 20 cubic feet, add 8- 10 oz. daily using the same procedure. <br />SEPTIC TANKS: Initial treatment, add 1 pint per 25 cubic feet capacity. Thereafter, use 8 oz. per week. Pour directly into toilet and flush. <br />DRAINLINES AND DOWN PIPES: Use product a minimum of 2 times weekly, to a maximum of 4 times. Start on the lowest floor and work 1 floor per day. Do not treat the same floor twice. When the top floor is reached, continue treatment for the top floor only. <br />PIPE SIZE/DOSAGE/FREQUENCY: 2"/4 oz./2 times/wk.; 4"/8 oz./2 times/wk.; 6"/12 oz./2 times/wk.; 8"/16 oz./2 times/wk. <br />CARPETS: For pet odors, pour directly on odor spot. Blot with a clean white cloth. Repeat if the odor persists. <br />CARPET MACHINES: To deodorize carpets, add 1/4 cup of product to the solution tank. RESTROOMS: To deodorize urinals and bowls, apply to surfaces and surrounding area. <br />FLOORS: Dilute 2 - 5 ounces per gallon and mop directly onto floor. Pour excess directly down the drain. <br />NOTE: Do not subject this product to disinfectants, boiling water or chlorinated products. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers. Be sure to pretest before using. GREASE TRAPS: For less than 20 cubic feet capacity, add 4 - 5 oz. of product daily by pouring into a sink or pipeline closest to the trap. Perform when the traps are used the least. Flush down with 1 cup of lukewarm water. For traps larger than 20 cubic feet, add 8- 10 oz. daily using the same procedure. <br /><br />SEPTIC TANKS: Initial treatment, add 1 pint per 25 cubic feet capacity. Thereafter, use 8 oz. per week. Pour directly into toilet and flush. <br /><br />DRAINLINES AND DOWN PIPES: Use product a minimum of 2 times weekly, to a maximum of 4 times. Start on the lowest floor and work 1 floor per day. Do not treat the same floor twice. When the top floor is reached, continue treatment for the top floor only. <br /><br />PIPE SIZE/DOSAGE/FREQUENCY: 2"/4 oz./2 times/wk.; 4"/8 oz./2 times/wk.; 6"/12 oz./2 times/wk.; 8"/16 oz./2 times/wk. <br /><br />CARPETS: For pet odors, pour directly on odor spot. Blot with a clean white cloth. Repeat if the odor persists. <br /><br />CARPET MACHINES: To deodorize carpets, add 1/4 cup of product to the solution tank. <br /><br />RESTROOMS: To deodorize urinals and bowls, apply to surfaces and surrounding area. <br /><br />FLOORS: Dilute 2 - 5 ounces per gallon and mop directly onto floor. Pour excess directly down the drain. <br /><br />NOTE: Do not subject this product to disinfectants, boiling water or chlorinated products. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers. DIRECTIONS: Fill product into properly labeled bottle. Pump trigger to prime. Spray a fine mist over entire surface, spread at once and polish dry. For best results use untreated paper towels, microfiber or dry lint free cloths. Change towels or cloths when dirty to avoid redepositing soil. Do not contaminate water, food or feed by use, storage or disposal. Rinsing with potable water is required if used on equipment that will be returned to a food processing area. <br /><br />NOTE: Do not use on wood or other varnished surfaces. Always spot test other surfaces before using. Unplug electrical appliances before using. Suitable for use in non-food processing areas. It is a violation of Federal law to use this product in a manner inconsistent with its labeling. <br /><br /><b>SANITIZING FOOD CONTACT SURFACE DIRECTIONS:</b> Use this product (200 ppm active) for sanitizing and cleaning of equipment and utensils in food processing, dairy industry, bars, restaurants, institutional kitchens, meat and poultry processing plants. Prior to application, remove gross food particles and soil by a pre-wash, pre-scrape, or pre-flush, and when necessary pre-soak. Thoroughly wash or flush equipment or utensils with a good detergent or compatible cleaner followed by a potable water rinse before applying sanitizer. Apply this product to pre- cleaned hard non-porous surfaces with cloth, mop sponge, or sprayer or by immersion. Surfaces must remain wet for 60 seconds (one minute). Drain thoroughly and allow to air dry before reuse. Not effective against rust stains. Dilute with cold water only. For GENERAL PURPOSE dilute 1:32 - 1:64 oz or 4 oz./gal - 2 oz./gal depending on soil level. Spray and wipe. GLASS: Dilute 1:64 or 2 oz./gal. Spray and wipe. SHOWERS: Dilute 1:32. For large areas use a portable pump up sprayer. Spray on tile, grout, fixtures and tub surfaces. Let stand for 5 minutes and rinse. For heavier stains agitation with a brush or sponge may be necessary to completely remove the stain. FLOORS: Dilute 1:64. Add directly to grout scrubber for removal of mold stains, soap scum, hard water deposits, or other common restroom soils. CARPET SPOTTING: Dilute 1:10 or 12 oz/gal. for heavy soils, dilute 1:20 or 6 oz./gal. for light to medium soils. For coffee as well as other water based stains. Apply a small amount of liquid to the stain. Agitate with a bone scraper and let stand for 3 - 5 minutes. Blot dry and rinse with clean water. Repeat as needed until the stain is completely removed.<br />Improper use or dilution of this product may affect cleaning performance, result in excess waste or may damage surfaces also may increase risk of health effects. Gloves and goggles recommended personal protection equipment. Please consult your local solid waste agency, drain commissioner, or water quality contact for determination on appropriate disposal of unused material. Please recycle empty containers. Removes tough crayon, lipstick, graffiti, oil and heel marks from a variety of surfaces. Not recommended for use on glass or water based paints. <br />Fill either trigger spray bottles or mop buckets/auto scrubbers through the FASTDRAW SYSTEM. Leaves no residue or streaks. Spray surface. Wipe clean with a lint free towel or sponge. Rotate Nozzle to ON position. Spray a fine mist. Polish dry. For best results, change towels frequently to prevent redepositing dirt. Do not contaminate water, food or feed by use, storage or disposal. Rinsing with potable water is required if used on equipment that will be returned to a food processing area. <br /><br />NOTE: Do not use on wood or other varnished surfaces. Always spot test other surfaces before using. Unplug electrical appliances before using. <br /><br />FOR COMMERCIAL AND INDUSTRIAL USE ONLY The Calcium, Lime & Rust Stain Remover should be rinsed off quickly after applying, so keep a Pail of clean water handy for easy rinsing.
Multipurpose Cleaners Sort by Display Order Price: High to Low Price: Low to High Name: A to Z Name: Z to A Created on
Display 6 12 18 per page
RCM11850225
Liquid - 64 fl oz (2 quart) - 4 / Carton - Clear
BET5284700
Concentrate Liquid - 67.6 fl oz (2.1 quart) - 4 / Carton - Yellow
DVO100986237
Concentrate Liquid - 84.5 fl oz (2.6 quart) - Surfactant Scent - 2 / Carton - Green
DVO905779CT
Ready-To-Use/Concentrate Liquid - 84.5 fl oz (2.6 quart) - Ammonia ScentBottle - 2 / Carton - Blue
DVO100898636
Ready-To-Use Liquid - 128 fl oz (4 quart) - Characteristic, Cherry Almond Scent - 4 / Carton - Clear
DVOCBD991206CT
Spray - 19 fl oz (0.6 quart) - Citrus Scent - 6 / Carton - Tan
DVO95892175
Spray - 50.7 fl oz (1.6 quart) - Citrus Scent - 2 / Carton - Purple
CHI0911
Cloth - 24" Width x 24" Length - 25 / Bag - 100 / Carton - Yellow
BET1980400CT
Concentrate Liquid - 128 fl oz (4 quart) - Clean ScentBottle - 4 / Carton - Green
DVO990682
Concentrate - 1.50 oz (0.09 lb) - 36 / Tub - 2 / Carton - Heavy Duty, Non-corrosive - Purple
RCM11974199
Concentrate Liquid - 64.2 fl oz (2 quart) - Lavender Scent - 4 / Carton - Purple
BET3160400
For Multipurpose, Multi Surface - Liquid - 128 fl oz (4 quart) - 7 to 8 pH - Pleasant Lemon Scent - pH Neutral, Kill Germs, Disinfectant, Deodorize - Light Amber Bottle - 4 / Carton
SMP19128CT
Concentrate Liquid - 128 fl oz (4 quart) - 6 / Carton - Clear
DVO94496138
Ready-To-Use Spray, Cream Cleanser - 32 fl oz (1 quart) - Bottle - 12 / Carton - White
DVO990653CT
Concentrate Powder - 0.50 oz (0.03 lb) - Pine Forest Scent - 90 / Canister - 2 / Carton - Orange
ZPE85924
128 fl oz (4 quart) - 4 / Box - Heavy Duty, Water Based, Water Softening, Water Soluble, Petroleum Free, Caustic-free, Phosphate-free, Non-toxic - Blue Green
DVO95773791
Concentrate Liquid - 84.5 fl oz (2.6 quart) - Fresh ScentBottle - 2 / Carton - Red
/* Added for Digitol */ /* End Added for Digitol */
